跳至主要内容

How To Purchase Printer Maintenance Kits

When you notice the message "perform printer maintenance" on your printer screen, that's the information to inform you to replace the maintenance kit, some parts of your printer is worn and impact the print quality after it was in use for a certain time, maintenance kit is a set of consumable parts for replacement that includes fuser unit, transfer roller, pickup rollers, separation pad and so on.

When purchase printer maintenance kit, we need to take some things into consideration.
1. Be sure that the model number of maintenance kit you want to buy is same as the model of your machine, additionally, make sure the kit includes all the parts your printer will need.
2. As all the parts in the maintenance kit mentioned above can not be used forever, that is to said that we would finally have to replace them all in the future, maintenance kits are supplied to save money and time for the users, it will be less cost to buy the set than to buy each single part separately.
3. Be clear which parts are worn or torn, the fuser unit, transfer roller, pickup rollers & separation pad in the kit are usually prone to wear, but we don't need to replace all of them as some parts are still in well working condition, so put aside the parts unnecessary unit the old one wear.
4. Original and compatible maintenance kits are available on the market, you can select them according to your circumstance, compatible kit is absolutely cheaper than original one, but some compatible manufacturers can serve their products with same quality.

评论

此博客中的热门博文

Process Of Applying Grease in Fuser Film Sleeves

Fuser grease is made of silicone oil for lubrication, and it also has excellent performance at thermal conductivity to assist fuser film sleeve to conduct the fusing process. Just like other laser printer parts, we need to replace the grease with use and time, proper operation is very important to be careful when installing, otherwise your fuser film sleeve will be damaged and scrapped totally. Hope the following instruction can be of help to you. Step 1. Detach the fuser assembly and remove the used fuser film. Step 2. Use alcohol to clean the surface of heating element. Step 3. Use soft spatula to scoop up grease from the container, total applying amount is around 1 gram. Step 4. Place the spatula at an angle on the surface, and wipe evenly the grease over the surface of heating element with forward and backward movement. Step 5. Put the heating element into the fuser film sleeve, and the end of the film with ground ring should be in good contact with the surface of lo...

Benefits Of Compatible Printer Parts

As you know, printer oftentimes need to do maintenance on it with time and use, that is to say, we need to have spare parts for replacement on your printer. On the market, compatible maintenance kits are available to meet users’ requirements, that include a fuser assembly, a transfer roller and some pickup rollers and separation pads, in addition, fuser film sleeve and fuser rollers inside the fuser assembly are wearing parts, so sometimes you only need to replace these little things rather than fuser assembly . All these key parts can be supplied by compatible manufacturers, nowadays, compatible parts are getting more and more quality and lower costs, so many printer users are in preference to compatible parts instead of original parts, maintaining and replacing parts properly are taken into consideration can low down much money for your office supplies every year.

Replacing Fuser Assembly For HP LaserJet P2055 - Part 2: Reassemble The Fuser Unit

Previous part we talked about disassemble the fuser unit on the HP LaserJet P2005, this time I'd like to show you how to reassemble this component. As I showed you last time, there're so many screws need to remove before you can access the fuser assembly, and conversely we need to fix them one by one on the machine after replacement, so that will take you some time to do finish. On the side of the fuser assembly , there're some driving gears that we need to pay attention of, some cutouts on it have to be in right position when slide back into its socket. Let's go ahead to reinstall the repaired or new fuser unit, don't forget to fix the screws, we got two on the left side, one at the top left and then there's one down at the bottom, and then put the metal plate on and make sure it can be fit to the left and right sides, fix it with the screws then, okay at this point in time what we can do is plug in all the wires, just don't forget to retrack the wir...