跳至主要内容

How To Clean A Upper Fuser Roller

Inside the printer fuser assembly, there are two pieces of rollers, upper fuser roller or fuser roller, and lower fuser roller or pressure roller, the upper fuser roller is a high quality aluminium tube coated with teflon, with a heating element inside, sometimes, we can use a fuser film sleeve to instead of the upper fuser roller. The lower pressure roller is a soft rubber roller.

The best way to clean a fuser roller is to use isopropyl alcohol if you haven't a specific cleaning fluid, just don't use rubbing alcohol, it may contain ingredients that can leave a residue on the fuser surface, you can also use a very light coat of silicon oil and a non linty rag. When the rollers are clean, dry them with another cloth. You can fully disassemble the roller before clean it, but it could be done with minimal removal just so the roller could be turned. The surface of the fuser roller is made of a teflon film that is easily damaged, so use only light pressure when cleaning, and better not to use harsh chemicals like acetone or trichloroethane, pay attention when you clean a fuser film sleeve, as it's very fragile and easily demaged, insert the sleeve into a support, wipe away the old grease from the heating element and apply the new high temperature grease, if you don’t have the grease, remain the old grease.

评论

此博客中的热门博文

Process Of Applying Grease in Fuser Film Sleeves

Fuser grease is made of silicone oil for lubrication, and it also has excellent performance at thermal conductivity to assist fuser film sleeve to conduct the fusing process. Just like other laser printer parts, we need to replace the grease with use and time, proper operation is very important to be careful when installing, otherwise your fuser film sleeve will be damaged and scrapped totally. Hope the following instruction can be of help to you. Step 1. Detach the fuser assembly and remove the used fuser film. Step 2. Use alcohol to clean the surface of heating element. Step 3. Use soft spatula to scoop up grease from the container, total applying amount is around 1 gram. Step 4. Place the spatula at an angle on the surface, and wipe evenly the grease over the surface of heating element with forward and backward movement. Step 5. Put the heating element into the fuser film sleeve, and the end of the film with ground ring should be in good contact with the surface of lo...

Replacing Fuser Assembly For HP LaserJet P2055 - Part 1: Disassemble The Fuser Assembly

When replacing fuser assembly for your HP LaserJet P2055 printer, you can actually get this done by yourself to save your money, but it requires some time and tools, and it would be better to do it at a good work place with good light. There's a lot of processes for this work, so today I'm going to show you how to disassemble the fuser assembly. Sometimes you still have some print quality issues though you replaced the toner, such as that the paper comes out with loosen  toner or some flaws, that's part of the fuser assembly or the sleeve, so we need to know how solve the problem with the fusing unit, before we replace a new one, just need to remove the old one, but it's definitely not too easy to do it by yourself. Let's get started with a philips and a flat blade screwdriver, and a pair of nipper pliers also, turn off the power button, open the font cover plate to remove the toner cartridge inside, use the flat plate screwdriver to remove the co...

Replacing Fuser Assembly For HP LaserJet P2055 - Part 2: Reassemble The Fuser Unit

Previous part we talked about disassemble the fuser unit on the HP LaserJet P2005, this time I'd like to show you how to reassemble this component. As I showed you last time, there're so many screws need to remove before you can access the fuser assembly, and conversely we need to fix them one by one on the machine after replacement, so that will take you some time to do finish. On the side of the fuser assembly , there're some driving gears that we need to pay attention of, some cutouts on it have to be in right position when slide back into its socket. Let's go ahead to reinstall the repaired or new fuser unit, don't forget to fix the screws, we got two on the left side, one at the top left and then there's one down at the bottom, and then put the metal plate on and make sure it can be fit to the left and right sides, fix it with the screws then, okay at this point in time what we can do is plug in all the wires, just don't forget to retrack the wir...