跳至主要内容

Replace Fuser Film Sleeve For Your HP P4015 Fuser Assembly

Fuser film sleeve for HP P4015 is also compatible with P4014 and P4515 fuser assembly. When it's time to replace your worn fuser film, there're various manufacturers that we select, the fuser assembly is the pricy unit that fuser film sleeve set in it, so it's very important to pick up the right quality film to fit it, additionally the procedures of replacement is also important, the fuser assembly may be damaged if operate improperly.

When we get started to do it, lets firstly take out the fuser assembly from your printer, you can see a metal cover plate at the side, use a phillip screw driver to remove the screws on it, also remove the red wire right next to it, and then you can slide the cover plate to the left and take it off.

Use a flat blade screw driver to release the clips of a group of driving gears and take them off from the fuser assembly. And then there are two screws nearby the blue clip at the bottom left, so these also need to be released to remove the back cover, then you can see two wires at left and right side and unplug them out, another one is need to be unplugged out at the left bottom.


Remove the topside screws to detach the lip and two springs, now you can see the fuser film sleeve inside, unplug out the red cord at its left bottom, now you can lift up the upper roller out of its socket, get the side collar off carefully and don't damage the heating element, now you can pull the sleeve off from the roller, wipe off the old lubrication on the heat element, and brush the new lubrication on it, and then it's time to replace the new fuser film sleeve on it, finally, just fix all the removed parts back.
标签：

评论

发表评论

此博客中的热门博文

Process Of Applying Grease in Fuser Film Sleeves

Fuser grease is made of silicone oil for lubrication, and it also has excellent performance at thermal conductivity to assist fuser film sleeve to conduct the fusing process. Just like other laser printer parts, we need to replace the grease with use and time, proper operation is very important to be careful when installing, otherwise your fuser film sleeve will be damaged and scrapped totally. Hope the following instruction can be of help to you. Step 1. Detach the fuser assembly and remove the used fuser film. Step 2. Use alcohol to clean the surface of heating element. Step 3. Use soft spatula to scoop up grease from the container, total applying amount is around 1 gram. Step 4. Place the spatula at an angle on the surface, and wipe evenly the grease over the surface of heating element with forward and backward movement. Step 5. Put the heating element into the fuser film sleeve, and the end of the film with ground ring should be in good contact with the surface of lo...
发表评论
阅读全文

Replacing Fuser Assembly For HP LaserJet P2055 - Part 1: Disassemble The Fuser Assembly

When replacing fuser assembly for your HP LaserJet P2055 printer, you can actually get this done by yourself to save your money, but it requires some time and tools, and it would be better to do it at a good work place with good light. There's a lot of processes for this work, so today I'm going to show you how to disassemble the fuser assembly. Sometimes you still have some print quality issues though you replaced the toner, such as that the paper comes out with loosen  toner or some flaws, that's part of the fuser assembly or the sleeve, so we need to know how solve the problem with the fusing unit, before we replace a new one, just need to remove the old one, but it's definitely not too easy to do it by yourself. Let's get started with a philips and a flat blade screwdriver, and a pair of nipper pliers also, turn off the power button, open the font cover plate to remove the toner cartridge inside, use the flat plate screwdriver to remove the co...
发表评论
阅读全文

Replacing Fuser Assembly For HP LaserJet P2055 - Part 2: Reassemble The Fuser Unit

Previous part we talked about disassemble the fuser unit on the HP LaserJet P2005, this time I'd like to show you how to reassemble this component. As I showed you last time, there're so many screws need to remove before you can access the fuser assembly, and conversely we need to fix them one by one on the machine after replacement, so that will take you some time to do finish. On the side of the fuser assembly , there're some driving gears that we need to pay attention of, some cutouts on it have to be in right position when slide back into its socket. Let's go ahead to reinstall the repaired or new fuser unit, don't forget to fix the screws, we got two on the left side, one at the top left and then there's one down at the bottom, and then put the metal plate on and make sure it can be fit to the left and right sides, fix it with the screws then, okay at this point in time what we can do is plug in all the wires, just don't forget to retrack the wir...
发表评论
阅读全文